SiC/CVD SiC复合涂层的抗氧化及抗热震性能研究

为了提高C/SiC复合材料耐高温性能,采用泥浆浸渍裂解与真空化学气相沉积(CVD)在材料表面制备了SiC/CVD SiC复合涂层,通过XRD、SEM分析了涂层组成与结构;研究了复合涂层的高温抗氧化(700～1 500℃)和抗热震性能。结果表明,泥浆浸渍法制备的SiC涂层具有一定的封孔效果,可使材料开孔率下降,但高温抗氧化效果并不佳,1 200℃氧化10 min后材料弯曲强度保留率下降明显仅有86%。CVD SiC涂层结构致密,与SiC封孔涂层结合较好,在700～1 500℃具有较好的抗氧化效果,随着氧化温度的升高,氧化后涂层完好,表面O元素逐渐增加,材料失重率缓慢增加但不大于0.5%,且材料性能并未下降。涂层材料在1 200℃-10 min短时热震5次后材料弯曲强度保留率仍有95%以上,且未出现开裂、剥落等热震损伤。在1 200℃-30 min长时热震10次后,涂层材料基本被完全氧化,材料失去保护作用,弯曲强度下降至90%左右。     

基于双环滑模控制的直/气复合控制系统设计

直/气复合控制导弹具有强干扰、强非线性以及强耦合等特点，传统的姿态控制器难以适用于该种复杂干扰并存的情况，文章提出了基于双环滑模控制的直/气复合控制器。首先采用有限时间收敛趋近律分别构造内外环滑模控制器，并将角速度回路的滑模变量量化为直接力指令，以解决空气舵与姿控发动机之间的耦合问题。接着使用非线性扩张状态观测器估计综合干扰，从而设计控制器补偿侧向喷流干扰及模型不确定性等综合干扰的影响。然后基于李雅普诺夫方法证明了控制系统闭环稳定，分析了干扰补偿对控制器收敛域的影响。最后仿真结果表明，该方法跟踪速度快，动态过程平稳，具有较强的干扰抑制能力，具有很强的鲁棒性。     

基于连续损伤模型的复合材料波纹梁压溃分析

复合材料的耐撞性受到了广泛重视,而波纹梁因其优异的抗屈曲构型被广泛应用于飞机翼梁和直升机底板等经常发生碰撞的结构中。进行了复合材料波纹梁的屈曲分析,研究了高度对波纹梁破坏模式的影响。建立复合材料波纹梁的连续损伤单波模型,层内基于Hashin判据建立含损伤因子的损伤刚度矩阵,层间根据二次名义应力准则和B-K准则模拟损伤演化,并通过典型复合材料波纹梁压溃试验验证了所建立模型的正确性。基于单波分析模型,通过施加周期性边界条件和反对称边界条件,研究了多波结构的吸能特性。     

Near-wall topological patterns and flow structures over a simplified Danaus plexippus model

Studies on the high-lift mechanisms of butterfly gliding flights shed light on the design of the micro air vehicles. The flow field around a simplified Danaus plexippus model is investigated using the hydrogen bubble visualization and the Particle Image Velocimetry (PIV) techniques. There are three near-wall topological patterns with different Angles of Attack (AoAs): the separation bubble, the Leading-Edge Vortex (LEV) and the high AoAs flow. For the separation bubble pattern, two saddles and two foci form in the middle of the model. The features of the LEV pattern are the leading-edge separation lines. The topological characteristics of the separation lines are changed by the interaction between the LEV and the Wing-Tip Vortex (WTV). For the high AoAs flow pattern, four unstable foci are found at the forewing and the hindwing respectively. The angle between the trajectory of the WTV and the model increases with increasing AoA even though the slope of the WTV angle versus AoA curve declines at the moderate AoAs.     

运载火箭推进剂复杂流动传热问题数值模拟中的模型简化方法

在运载火箭改进优化或新型运载火箭设计过程中,会遇到各种复杂的流动与传热问题。按照真实产品和物理过程直接建立的数值计算模型过于复杂,不同尺度的结构、流动与传热、长时间的飞行过程相互耦合,出现计算时间太长(数年)、收敛困难、程序调试困难等问题。针对初始条件复杂、飞行过程复杂、边界条件复杂3类具体问题,总结了3种相应的模型简化方法,分别是工程经验法、极限参数法、低维近似法,为推进剂复杂流动与传热的数值模拟提供参考。     

点阵结构空气舵及内部流体热流固耦合研究

开展了钛合金TC4材料激光粉末床熔融(LPBF)工艺研究,在此基础上设计了多孔轻质空气舵模型,并基于有限差分法(FDM),采用三维流固耦合共轭传热数值计算方法,利用流体体积法(VOF)追踪流体自由液面,研究了典型的点阵夹层结构的空气舵内部冷却液动态换热过程的相互影响过程,考虑了冷却液与钛合金材料蒙皮间的耦合传热及湍流换热。结果表明,空气舵的内部流体压强随速度的增加而增加,从而导致流体出口的速度增加。当压强增加到一定程度时,流体的出口以水柱形式喷出。虽然较大的流体速度可以带走较多的热量,但是影响远小于对压强的影响。综合考虑空气舵的服役要求,获得了合适的冷却水入口速度。     

一种针对局部结构的有限元模型修正方法

针对实际结构有限元模型（FEM）的建模误差通常仅存在于局部区域，提出了一种对局部结构单独进行模型修正的方法。首先，根据频响函数（FRF）解耦理论得到由残余结构频响函数与包含待修正参数的局部结构动刚度所重构的整体结构频响函数的拟合值，然后通过迭代优化使其与测量值的残差最小化，从而得到参数的极大似然估计。在此基础上，将残差关于参数的灵敏度以局部结构动力学矩阵表示，建立了模型修正的基本方程，利用整体结构的测试数据即可直接对分离出来的局部结构进行模型修正。最后，对喷气式飞机和三角机翼飞机分别进行了数值模拟和实验研究，验证了所提方法的可行性和有效性。结果表明，所提方法可以成功地用于仅局部区域含有建模误差的实际结构有限元模型的修正，修正后的有限元模型的动态特性与实际结构有较好的一致性。     

Experimental study on plasma jet deflection and energy extraction with MHD control

This paper presents an integrated research scheme for vector deflection and energy extraction in a gas plasma jet under Magneto-Hydrodynamic (MHD) control. A MHD-controlled thrust-vector test rig was used to conduct the experimental research. A gas plasma was obtained by injecting ionization seeds of Cs₂CO₃ into the combustion chamber via artificially forced ionization. The effects of the gas temperature and ionization seed mass fraction on the plasma jet deflection and energy extraction were experimentally verified under an applied magnetic field. The experimental results were analyzed theoretically. The results showed that the deflection amplitude of the gas plasma jet and the extracted voltage signal intensity increased with increasing gas temperature and the ionization seed mass fraction. The extracted dynamic voltage signals proved that the ionization seeds of Cs₂CO₃ induced gas ionization at 1173 K. The experiment verified that it is feasible to simultaneously achieve jet deflection and extract energy under the action of an external magnetic field.     

300 MVA脉冲发电机组滑差方式起动过程研究

介绍了300 MVA脉冲发电机组的滑差装置。对机组采取滑差方式的起动过程进行了分析和等效建模。根据机组实际起动过程电气波形,利用非线性规划模型,建立了滑差装置液体电阻等效仿真模型,并代入机组参数对起动过程进行仿真,仿真结果和实际波形吻合,验证了模型的正确性。在此基础上,为了使机组的转速达到额定转速,提出在滑差装置液体电阻低位时并入两级固体金属电阻后短接的方案,给出了两级固体金属电阻的阻值等理论参数,并通过仿真验证了方案的可行性。建立的仿真模型可以作为研究不同参数、不同控制策略下的机组起动过程动态特性的重要工具。     

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.